View the available End Fittings below:
- 3-A Sanitary fittings
-
3-A Sanitary fittings
3-A Sanitary Standards requires the hose end fitting to be sealed against the ingress of external fluid into the fitting construction. Aflex Hose has implemented a silicone seal between the ferrule and fitting to address this requirement.
The direct crimp style fitting does not incorporate the silicone seal as standard and a modified version of the fitting for 3-A is required.
When ordering, customers should specify that the hose assembly must meet 3-A sanitary requirements. The 3-A symbol and appropriate marking to 3-A requirements will be applied to the hose assembly.
Bioflex Ultra covered hoses are soakable in both standard and 3-A sanitary configurations. The 3-A assembly is only available with an EPDM or silicone cover.
The Aflex Hose 3-A certificate is available to view in our website literature section. The Aflex Hose 3-A certificate is also available to view on the 3-A Sanitary website. Follow the link to the database search page and search for “Aflex Hose” under view company listings.
3A Sanitary Triclamp Fittings
3A DIN11851 Female
3A Non-lined Swivel Flange
3A Mini Sanitary Triclamp
- 90° Elbow fittings
-
90° Elbow fittings
PTFE-lined 90° elbow fittings
All of the PTFE-lined end fittings described on previous pages can be fitted as 90˚ elbow PTFE-lined fittings to the design shown, to the sizes listed.
All grades of hose can be used, except PB.
Non-lined 90° elbow fittings
A 90˚ elbow attached to the hose can be supplied non-PTFE lined, as shown, for any size or grade of hose or type of fittings, to special order.
Hose bore size Off-set Fitting length Weight of fitting mm mm kg lbs 7/8" or 1" 85 143 0.485 1.07 13/8" or 11/2" 200 237 1.372 3.03 17/8" or 2" 200 314 1.678 3.70
- BSP 60° cone seat female fittings
-
BSP 60° cone seat female fittings
End fitting specifications
- BSPP Threads to British Standard Pipe Parallel Thread design to BS21, 60˚ cone seat design, or flat seat.
End fitting materials
- Spigots in Grade 316L SS
- Nuts in Grade 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
Alternatives:
- Hydraulic design cone seat female unions can be supplied in zinc plated carbon steel to special order.
- Lug nuts can be supplied in gun metal (bronze) if required.
Surface finish:
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Alternatives
- Cone seat female union fittings can be supplied with a BSPP BSPT Taper Male Adaptor if required.
Nominal hose size NPT or BSPT
thread size*Fitting length A
(Bioflex Ultra RC)Fitting inside diameter I Weight of fitting in mm in in mm in mm kg lbs 1/2 13 1/2 1.46 37 0.37 9.40 0.09 0.21 3/4 20 3/4 1.89 48 0.62 15.75 0.20 0.44 1 25 1 2.17 55 0.85 21.50 0.33 0.72 11/4 32 11/4 2.48 63 1.03 26.21 0.49 1.07 11/2 40 11/2 2.87 73 1.25 31.75 0.79 1.73 2 50 2 2.91 74 1.76 44.60 1.07 2.36 **21/2 65 21/2 3.15 80 2.25 57.15 1.37 3.02 **3 80 3 3.21 81.5 2.63 66.7 2.10 4.62
- BSP flat face lug nut female fitting
-
BSP flat face lug nut female fitting
Nominal hose size BSPP thread size Fitting length A
(Bioflex Ultra RC) *Fitting bore diameter I Weight of fitting in mm in in mm in mm kg lbs 1 25 1 2.67 68 0.85 21.50 0.23 0.51 11/2 40 1 1/2 3.94 100 1.25 31.75 0.55 1.21 2 50 2 4.33 110 1.75 44.60 0.77 1.69 * Fitting Lengths listed are for Bioflex Ultra RC, SI and BK hose grades. Shorter lengths apply for other hose grades.
- Cam and groove fittings
-
Cam and groove fittings
Cam and groove male fitting
End fitting specifications
- Generally in accordance with A-A-59326 (replaces MIL-C-27487) and EN14420-1 (replaces DIN 2828), and all are fully interchangeable.
End fitting materials
- Fittings in Grade 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
- Adaptor flange only in Grade 304 SS
Surface Finish: Non-lined fittings only
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Temperature and pressure ratings
- Temperature and pressure determined by the type of gasket in the female connecting component and the hose grade.
PTFE Lined cam and groove male fitting
PTFE lined male cam and groove x flange
PTFE lined integral cam and groove male fitting
Cam and groove female fitting
End fitting specifications
- Generally in accordance with A-A-59326 (replaces MIL-C-27487) and EN14420-1 (replaces DIN 2828), and all are fully interchangeable.
End fitting materials
- Spigot in Grade 316L SS
- Body in Grade 316C SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
- Standard Gasket is Buna-N (nitrile) rubber.
- FEP encapsulated silicone rubber gaskets also available.
Surface finish: (non-lined fittings only)
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Temperature and pressure ratings
- When used with a Buna-N gasket all sizes up to 16 Bar (230 psi) and up to a maximum temperature of 65˚C (149˚F)
- When used with FEP, fluoro rubber or other encapsulated gaskets all sizes up to 10 bar (145 psi) and up to a maximum temperature of 204˚C (400˚F).
90˚ elbow cam and groove fittings (PTFE-lined only)
- 90˚ elbow Integral PTFE-lined cam and groove fittings are available for sizes 1”, 11/2” and 2” - see 90˚ elbow fittings.
Notes: For integral PTFE-lined fittings only
- FEP gaskets require higher clamping forces to flatten the seal and make the joint. This is made easier by “pre-setting” these gaskets by clamping polypropylene cam male inserts to the assembled fittings, which must then be kept in place during storage, until use.
- Any Customer’s own “special” gaskets must be pre-supplied to Aflex for special assembly and testing of hose assemblies, to ensure suitability.
Swivelling locking arm female can and groove fitting
Non-Lined Cam & Groove Male Fitting
Nominal hose size
Outside diameter D *Non-Lined fitting length A Non-lined inside diameter I *PTFE lined fitting length AL PTFE lined inside diameter B Weight of Fitting in mm in mm in mm in mm in mm in mm Kg Lbs 3/4 20 1.260 32.0 2.44 62.0 0.62 15.8 2.82 71.58 0.71 18.13 0.35 0.77 1 25 1.456 37.0 2.95 75.0 0.85 21.5 3.74 95 0.81 20.61 0.45 0.99 11/4 32 1.790 45.5 3.34 85.0 1.03 26.2 3.62 92 0.97 24.8 0.45 1.09 11/2 40 2.106 53.5 3.74 95.0 1.25 31.8 3.98 101 1.35 34.40 0.84 1.85 2 50 2.480 63.0 4.33 110.0 1.76 44.6 4.61 117 1.72 43.75 1.10 2.42 21/2 65 2.980 75.8 4.13 105.0 2.23 56.6 6.50 165 2.17 55.0 1.17 2.57 3 80 3.600 91.5 4.76 120.8 2.87 73.0 6.98 177.4 2.84 72.2 1.45 3.20 PTFE Lined Male Cam & Groove X Flange Adaptors
Cam action adaptor size Flange size & specification ØD A ØI Weight of fitting in mm in mm in mm in mm kg lbs 1 25 1" ANSI 150 2 50 41/8 105 0.84 21 1.246 2.75 1 25 DN25/PN16 2.58 64 41/8 105 0.84 21 1.538 3.39 1 1/2 40 1 1/2 ANSI 150 2.87 73 43/8 118 1.35 34 2.228 4.92 1 1/2 40 DN40/PN16 3.47 88 43/8 118 1.35 34 2.753 6.07 2 50 2" ANSI 150 3.63 92 43/8 118 1.69 43 3.359 7.40 2 50 DN50/PN16 4 102 43/8 118 1.69 43 3.714 8.19 Swivelling, Locking Arm Female Cam and Groove Fittings
- Non-LinedNominal hose size *Fitting length A (RC) Cam sleeve inside dia. D Fitting inside diameter I Weight of fitting in mm in mm in mm in mm Kg Lbs 3/4 20 2.10 53.00 1.26 32.0 0.62 15.75 0.58 1.28 1 25 2.32 59.00 1.45 37.0 0.85 21.50 0.72 1.58 11/4 32 2.54 64.60 1.81 46.0 1.03 26.21 1.10 2.42 11/2 40 2.65 67.20 2.12 54.0 1.25 31.75 1.21 2.66 2 50 3.11 79.00 2.52 64.0 1.76 44.60 1.48 3.26 21/2 65 2.99 76.00 3.01 76.5 2.25 57.15 1.42 3.12 3 80 2.80 71.00 3.63 92.2 2.63 66.70 1.88 4.14 Fixed or Swivelling, Locking Arm Female Cam and Groove Fitting
- Integral PTFE LinedNominal hose size Fitting length A (RC) Cam sleeve inside dia.D Fitting inside diameter I Weight of fitting in mm in mm in mm in mm Kg Lbs 3/4 20 2.155 54.75 1.260 32.0 0.76 19.4 0.42 0.93 1 25 2.716 69.00 1.456 37.0 1.01 25.7 0.59 1.30 11/4 32 2.560 65.50 1.810 46.0 1.26 32.0 0.98 2.16 11/2 40 2.612 66.35 2.126 54.0 1.53 38.9 1.15 2.50 2 50 2.966 75.35 2.520 64.0 2.03 51.6 1.40 3.08 **21/2 65 5.310 135.0 3.010 79.5 2.36 60.0 1.17 2.57 **3 80 5.450 138.4 3.630 92.2 2.87 73.0 1.40 3.07
- DIN 11851 fittings
-
DIN 11851 fittings
PTFE-lined DIN 11851 fittings
PTFE Lined DIN 11851 female fittings
Description
DIN11851 male and female fittings, integral PTFE-lined and flared. The PTFE sealing face is hot moulded into the correct shape, designed to achieve the optimum pressure seal. 90˚ elbow PTFE-lined fittings are available for some sizes and grades.
Specifications
- Generally to German DIN 11851 specifications.
End fitting materials
- Spigots in Grade 316L SS (Non-Lined Spigot in 1.4571)
- Nuts in Grade 304 SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
Temperature and pressure ratings
- Sizes up to 11/2” MWP = 40 bar (580 psi) up to 140˚C (284˚F)
- Sizes 2” to 3” MWP = 25 bar (360 psi) up to 140˚C (284˚F)
PTFE lined DIN 11851 male fitting
Except: where the applicable hose pressure/temperature ratings are lower
- See Sizes, grades, pressures and weights.Note: The PTFE-lined male fitting is designed to be used without a rubber seal. Please note that when connecting to a PTFE Lined DIN 11851 Male, extra spanner tightening of the nut is sometimes required in order to provide a leak free connection.
Non-lined DIN 11851 fittings
Non-lined DIN 11851 female fitting
Specifications
- Generally to German DIN 11851 specifications.
End fitting materials
- Spigots in Grade 316L SS (Non-Lined Spigot in 1.4571)
- Nuts in Grade 304 SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
Surface finish
- All surface finishes are to ASME BPE-SF-3>0.76µm Ra, mechanical polish.
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Temperature and pressure ratings
- Sizes up to 11/2” MWP = 40 bar (580 psi) up to 140˚C (284˚F)
- Sizes 2” to 3” MWP = 25 bar (360 psi) up to 140˚C (284˚F)
Non-lined DIN 11851 male fittings
Except: where the applicable hose pressure/temperature ratings are lower
- See Sizes, grades, pressures and weights.PTFE-lined DIN 11851
Nominal hose size = 'I' dia *Male fitting
length A
(Bioflex Ultra RC)*Female fitting length A
(Bioflex Ultra RC)Fitting inside diameter Weight of fitting male Weight of fitting female †3A in mm in mm in mm in mm kg lbs kg lbs **1/2 15 2.28 58 2.00 51 0.51 13.0 0.13 0.29 0.17 0.37 √ 3/4 20 2.44 62 2.17 55 0.76 0.21 0.46 0.23 0.51 √ 1 25 3.00 76 2.75 70 1.01 25.7 0.30 0.66 0.40 0.88 √ 11/4 32 2.75 70 2.50 64 1.28 32.4 0.37 0.82 0.51 1.12 √ 11/2 40 2.84 72 3.00 76 1.53 38.9 0.42 0.93 0.73 1.60 √ 2 50 3.47 88 3.55 90 2.03 51.6 0.65 1.43 1.10 2.42 √ 21/2 65 5.91 150 5.20 132 2.51 63.7 1.50 3.29 1.42 3.12 √ 3 80 6.38 162 5.51 140 3.02 76.8 1.90 4.19 1.82 4.01 √ PTFE Non-lined DIN 11851
Nominal hose size = 'I' dia *Male fitting length A
(Bioflex Ultra RC)*Female fitting length A
(Bioflex Ultra RC)Fitting inside
diameterWeight of fitting male Weight of fitting female †3A in mm in mm in mm in mm kg lbs kg lbs 1/2 15 1.82 46 1.63 41.5 0.37 9.4 0.14 0.30 0.20 0.44 √ 3/4 20 2.05 52 1.87 47.5 0.62 15.8 0.28 0.62 0.34 0.76 √ 1 25 2.68 68 2.33 59.2 0.85 21.5 0.40 0.87 0.49 1.08 √ 11/4 32 2.48 63 2.58 65.5 1.03 26.2 0.55 1.21 0.64 1.40 √ 11/2 40 2.84 72 2.76 70.0 1.25 31.8 0.76 1.68 0.85 1.86 √ 2 50 3.23 82 3.23 82.0 1.76 44.6 0.92 2.04 1.20 2.04 √ 21/2 65 3.23 82 3.03 77.0 2.25 57.15 1.27 2.79 1.59 3.50 √ 3 80 3.23 82 2.97 75.5 2.63 66.7 1.62 3.56 2.04 4.49 √
- PTFE dip pipe fittings
-
PTFE dip pipe fittings
Fixed dip pipes
Description
Fixed dip pipes are fairly rigid, thick wall PTFE tubes, either straight or 90˚ elbowed, which are directly crimped to the end of Bioflex Ultra hoses. They are designed for insertion into drums, tanks and reaction vessels in order to suction drain (or inject) process fluids transferred through the hose.
Materials
- Standard dip pipes are in anti-static (AS) PTFE
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
How to order
Specify the size and material of the dip pipe, whether it is straight or 90˚ elbowed. Give the length of the straight leg of the dip pipe and the length of the rest of the hose assembly separately.
Maximum working pressures
Dip Pipes are normally only tested to 6 bar pressure, and are not suitable for use at pressures higher than 3 bar. They are usable at negative pressure up to -0.9bar vacuum.
If higher pressure ratings are required, consult Aflex Hose.
Lengths
Dip pipes are supplied as standard in one metre straight lengths, but can be supplied in any length to individual requirements.
Detachable dip pipes
Description
As fixed dip pipes. but connected to the hose through an end fitting, not by crimping direct to the hose.
Design
A straight, or 90˚ elbowed anti-static PTFE dip pipe, fitted with a Flange or Cam and groove male PTFE-lined and flared end fitting.
The most usual end fitting is a cam male (as shown), so the dip pipe can then be connected to a hose with a cam female end fitting.
Nominal hose bore size Approximate dip pipe dimentions Outside diameter D Inside diameter I in mm in mm in mm 3/4 20 0.87 22 0.51 13 1 25 1.14 29 0.83 21 11/2 40 1.54 39 1.00 27 2 50 2.17 55 1.58 40
- ENCAP end fittings
-
ENCAP end fittings
PTFE encapsulated (Encap) end fittings
- Easy to assemble - fully PTFE-lined end fitting - larger bore than conventional PFA Encap fittings
Introduction
In response to requests from customers Aflex have developed a basic range of PTFE encapsulated end fittings.
These can be used in place of standard non-lined end fittings to provide a PTFE-lined alternative for threaded end fitting types where integral lining is not possible. They also provide a cost-effective alternative to exotic metals such as hastelloy where high levels of chemical resistance are required.
Encap fittings do not provide the same advantages as integral lined fittings. The full hose bore size through the fitting is reduced and entrapment areas are present at the end of the encapsulated hose tail.
Encap fittings provide a fully PTFE-lined fitting with a flared face, which is easier to assemble. The Aflex Encap fitting design has a significantly larger bore than the conventional PFA encapsulated fittings available from other suppliers.
Loose BSPP Fixed Male ENCAP Fitting with a Standard Non-Lined Ferrule
Swivel flange Encap fitting crimped on to Corroline+ Hose
Construction and application
Encap fittings are assembled and crimped using the same non-lined ferrules, crimp diameters and assembly procedures that are used with standard direct crimp fittings throughout the Aflex PTFE hose product range.The PTFE encapsulation is either natural or antistatic PTFE as required, with a PTFE wall thickness of 1.5mm (0.060”) for sizes up to 1¹/2” and 1.8mm (0.070”) for sizes 2” and above.
Encapsulated fittings are available for all Corroline+ Self Assembly Distributors.
Important Note: The use of Encap fittings with hoses, ferrules or other components which are not all supplied by Aflex Hose is strictly prohibited and no liability will be accepted for any failures resulting from such abuse.
Legend:
- Grooved standpipe fitting
-
Grooved standpipe fitting
Non-lined tube adapter (grooved standpipe) fitting
End fitting specifications
- Compatible with existing industrial standard tube fitting components.
Temperature and pressure ratings
- As for the relevant size of hose in specifications and properties.
End fitting materials
- Fitting in grade 316L SS
- Ferrule (for hose attachment) in Grade 304 or 316L SS
Alternatives:
- Can be supplied with matching female nuts and ferrules (clamping ferrules) to suit.
Surface Finish:
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Nominal hose size Fitting length A Diameter D Fitting inside diameter I Weight of fitting in mm in mm in mm in mm Kgs Lbs 1/4 6.4 1.93 49 0.25 6.35 0.16 4.10 0.031 0.07 3/8 9.5 2.05 52 0.375 9.53 0.28 7.00 0.044 0.10 1/2 12.7 2.28 58 0.50 12.7 0.37 9.40 0.074 0.16 3/4 20 2.48 63 0.75 19.05 0.62 15.75 0.16 0.35 1 25 2.87 73 1 25.40 0.85 21.50 0.25 0.55
- IDF female fittings
- JIC Fittings
-
JIC fittings
End fitting specifications
- SAE J514 37˚ flare JIC female fitting
- 37˚ JIC male-to-NPT male/female adaptors
- NPT Threads to ANSI/AMSE B1.20.1
Temperature and pressure ratings
- Same maximum working pressure and temperature as for the relevant size of Bioflex Ultra Hose in the Size, grades, pressures and weights table.
Note: Not usable with SAE 45˚ flare fittings which have the same thread.
End fitting materials
- Spigots in Grade 316L SS
- Nuts in 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
Alternatives
- Available in other materials to special order
Surface Finish
- All surface finishes are to ASME BPE-SF-O (No finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
JIC fittings
JIC to NPT male union
JIC to NPT female union
JIC fittings
Nominal hose size 37 ° JIC
thread size*Fitting length A
(Bioflex Ultra RC)Hex size H Fitting inner diameter I Weight of fitting in mm in in mm in mm in mm kg lbs 1/2 13 3/4 - 16 1.57 40 0.88 22.2 0.37 9.40 0.09 0.20 3/4 20 11/16 - 12 1.89 48 1.25 31.7 0.62 15.75 0.20 0.44 1 25 1 5/16 - 12 2.28 58 1.50 38.1 0.85 21.50 0.30 0.66 11/2 40 1 7/8 - 12 2.72 69 2.25 57.1 1.25 31.75 0.62 1.37 2 50 2 1/2 - 12 3.27 83 2.88 73.0 1.76 44.60 1.10 2.42 JIC to NPT Male Union
Nominal hose size *Male union length A1
(Bioflex Ultra RC)Fitting inner diameter I Weight of fitting in mm in mm in mm kgs lbs 1/2 13 3.07 78 0.53 13 0.15 0.33 3/4 20 3.78 96 0.72 18 0.33 0.73 1 25 4.17 106 0.94 24 0.51 1.12 JIC to NPT Male Union
Nominal hose size *Female union length A2(Bioflex Ultra RC) Fitting inner diameter I Weight of fitting in mm in mm in mm kg lbs 1/2 13 3.07 78 0.39 9.9 0.17 0.37 3/4 20 3.78 96 0.61 16 0.34 0.75 1 25 4.17 106 0.84 21 0.64 1.41
- List of PTFE tail fittings
-
List of PTFE tail fittings
Fitting sizes, types and part numbers
Hose size and grade Fitting material Fixed males Fixed
female NPTCone seat female union BSPP Cone seat male to-male adaptors 37˚ JIC female unions JIC-to-NPT male/Male adaptors Ferrules BSPT 06-100- NPT 06-110- 33-100- 07-500- 18-100- 07-597- 18-202- For SB Hose 01- For DB Hose 01- -3 HW SS
MS-
02-02-04- - 02-02-04 - - - 120-02-02-01
120-02-02-04- 3/16" HW SS
MS- - - - - - - 120-03-03-02
120-03-03-04-
120-04-04-041/4" SW & HW SS
MS04-04-01
04-04-0404-04-01
-04-04-01
-04-04-01
04-04-0404-04-01
04-04-0407-04-01
-07-04-01
-120-04-04-02
120-04-04-04125-04-04-02
*125-04-04-043/8" SW & HW SS
MS06-06-01
06-06-04
06-06-01
-06-06-01
-06-06-01
06-06-0406-06-01
06-06-0409-06-01
-09-06-01
-120-06-06-02 120-06-06-04 180-06-06-02 170-06-06-04 1/2" SW & HW SS
MS08-08-01
08-08-04
08-08-01
-08-08-01
-08-08-01
08-08-0408-08-01
08-08-0412-08-01
-12-08-01
-120-08-08-02
120-08-08-04180-08-08-02 150-08-08-04 3/4" SW & HW SS
MS12-12-01
12-12-04
12-12-01
-12-12-01
-12-12-01
12-12-0412-12-01
12-12-0417-12-01
-17-12-01
-240-12-12-02 120-12-12-04 240-12-12-02 180-12-12-04 1 1/4” HW SS
MS20-20-01
-20-20-01
-- 20-20-01
-- - - - 150-20-20-02 150-20-20-04 1 1/2” HW SS
MS24-24-01
-24-24-01
-- 24-24-01
-- 30-24-01
-20-24-01
--
150-24-24-02 150-24-24-04 2” HW SS
MS32-32-01
-32-32-01
-- 32-32-01
-- - - - 150-32-32-02 150-32-32-04 *1" Ferrules for HW, SB hose are 01-150-16-16-02 (and 04)
Example: Part Numbers for a 1/2” NPT fixed male in SS is 06-110-08-08-01.
Note: The last two digits of the part number indicates the material:
- 01=316 SS
- 02 = 304 SS
- 04 = zinc plated carbon steel.
- NPT and BSPT fittings
-
NPT and BSPT fittings
Fixed female NPT
End fitting specifications
- NPT Taper Threads to American National Standard Pipe Taper Thread design to ANSI/AMSE B1.20.1.
- BSPT Threads to British Standard Pipe Taper Thread design to BS21
Alternatives
- Parallel Threads, Metric Threads and others.
Alternatives
- Hydraulic design BSPT male fittings in zinc plated carbon steel, to special order.
Fixed male NPT or BSPT
Surface Finish
- All surface finishes are to ASME BPE-SF-O (No finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
End fitting materials
- Fittings in Grade 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
- Available in other materials to special order
Fixed Male NPT or BSPT
Nominal
hose sizeNPT or BSPT
thread size*Fitting length A
(Bioflex Ultra RC)Fitting inside diameter I Weight of fitting in mm in in mm in mm kg lbs 1/2 13 1/2 2.40 61 0.37 9.40 0.14 0.30 3/4 20 3/4 2.68 68 0.62 15.75 0.25 0.54 1 25 1 3.07 78 0.85 21.50 0.33 0.73 11/4 32 11/4 3.58 91 1.03 26.21 0.61 1.34 11/2 40 11/2 3.82 97 1.25 31.75 0.81 1.78 2 50 2 4.57 116 1.76 44.60 1.17 2.58 21/2 65 21/2 5.31 135 2.25 57.15 1.84 4.04 3 80 3 5.39 137 2.63 66.7 2.49 5.47 Fixed Female NPT
Nominal hose size NPT thread size *Fitting length A
(Bioflex Ultra RC)Fitting inside diameter I Weight of fitting in mm in in mm in mm kg lbs 1/2 13 1/2 2.40 61 0.37 9.40 0.18 0.39 3/4 20 3/4 2.52 64 0.62 15.75 0.24 0.54 1 25 1 3.23 82 0.85 21.50 0.37 0.81 11/2 40 11/2 3.62 92 1.25 31.75 0.83 1.82 2 50 2 4.13 105 1.76 44.60 1.24 2.72
- PTFE tail or hydraulic fittings
-
PTFE tail or hydraulic fittings
PTFE-tail end fittings for SW and HW Grades
Aflex Hose keep in stock a wide range of “PTFE-tail” design standard end fittings, ferrules and adaptors in both zinc plated carbon steel and 316L stainless steel.
These are specified, with the relevant Aflex Hose Part Number, in the List of PTFE tail fittings.
PTFE-tail end fittings can only be applied to the Standard Smoothbore, Standard Wall (SW) and Heavy Wall (HW) Hose Grades.
Hydraulic ferrule
These can only be used with the Standard Smoothbore, Medium Wall (MW) Hose Grade.
Hydraulic-tail end fittings are usually sourced from local hydraulic suppliers, but can be supplied by Aflex Hose if required.
Ferrules for MW, SB and MW Hose can be supplied by Aflex Hose, as below.
Stand tube
MW, SB hose Zinc plated carbon steel Stainless steel 3/16 BB -4 01-170-03-03-04 01-170-03-03-03 1/4 BB -5 01-170-04-04-04 01-170-04-04-03 5/16 BB -6 01-170-05-05-04 - 3/8 BB -8 01-170-06-06-04 01-170-06-06-03 1/2 BB -10 01-170-08-08-04 01-170-08-08-03 5/8 BB -12 01-170-10-10-04 01-170-10-10-03 3/4 BB 01-170-12-12-04 01-170-12-12-03 1 BB 01-170-16-16-04 01-170-16-16-03
- Non-lined triclamp fittings
-
Non-lined triclamp fittings
Non-lined sanitary triclamp fittings
Introduction
There are many different specifications, dimensions and surface finishes for triclamp fittings. Those listed below are the popular fittings, which are stocked as standard fittings by Aflex.
All the alternative fittings can be supplied to special order if the following information can be given:
- Flange diameter D and Outlet diameter I
- Hose size if known, or Aflex can recommend a hose size to suit
- The internal surface finish, if it is required to be better than the ASME BPE SF3 surface
- finish of <0.76μm.Ra = <30μ in Ra non-electropolished.
- Standard (see below) if known.
Standards
- ASME BPE
- DIN 32676 (types A, B and C are available)
- BS 4825 Pt.3 (equivalent to ASME BPE)
- ISO 1127
End fitting materials
- Fittings in AISI 316L = EN 1.4404 = BS 316 S11
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
- Fittings for DIN32676 are available in 1.4435 (316L)
- Fittings in 1.4571, Hastelloy, Monel, PVDF and other materials to special order
Temperature and pressure ratings
- Pressures up to 16 bar (230 psi)
- Temperatures up to 120˚C (250˚F) with EPDM gaskets
- Temperatures up to 180˚C (356˚F) with PTFE, silicone or viton gaskets
- Higher pressures and temperatures with special clamps and gaskets.
Mini sanitary triclamp fitting
Internal surface finish specifications
- ASME BPE SF3 (mechanical polish, not electropolished) surface finish, maximum reading: <0.76μm Ra = <30μ in. Ra
- ASME BPE SF4 (mechanical polish and electropolished) surface finish, maximum reading: <0.375μm Ra = <15μ in. Ra (SF4 is the highest level of surface finish specified in ASME BPE, and the standard, stocked fittings listed are all to this finish).
- DIN 32676 H4 (mechanical polish, not electropolished) surface finish, average reading:
<0.4μm Ra = <16μ in. Ra. If the standard SF4 finish is not acceptable, H4 must be requested on the enquiry/order.
Note: ASME BPE Triclamp suppliers often quote an ‘Average’ of surface finish reading only, for example ‘average 15 Ra or better’, but this is not in accordance with the stricter ASME BPE requirement that a ‘maximum’ for individual readings should be complied with.
Non-Lined
DIN 32676 SERIES A (DIN) Nominal hose size Flange diameter D Outlet diameter I *Fitting length A in METRIC DN in mm in mm in mm 1/4 6 0.984 25.0 0.236 6 1.299 33 5/16 8 0.984 25.0 0.315 8 1.654 42 3/8 10 1.339 34.0 0.394 10 1.969 50 1/2 15 1.339 34.0 0.630 16 1.969 50 3/4 20 1.339 34.0 0.787 20 1.969 50 1 25 1.988 50.5 1.024 26 2.283 58 11/4 32 1.988 50.5 1.260 32 2.441 62 11/2 40 1.988 50.5 1.496 38 2.638 67 2 50 2.520 64.0 1.969 50 3.071 78 21/2 65 3.583 91 2.598 66 2.953 75 3 80 4.173 106 3.189 81 3.169 80.5 DIN 32676 SERIES B (ISO) Nominal hose size Flange diameter D Outlet diameter I *Fitting length A in METRIC DN in mm in mm in mm 1/4 10.2 0.984 25.0 0.276 7 1.299 33 5/16 13.5 0.984 25.0 0.406 10.3 1.654 42 3/8 17.2 0.984 25.0 0.551 14 1.969 50 1/2 21.3 1.988 50.5 0.713 18.1 1.969 50 3/4 26.9 1.988 50.5 0.933 23.7 1.969 50 1 33.7 1.988 50.5 1.169 29.7 2.283 58 11/4 42.4 2.520 64.0 1.512 38.4 2.441 62 11/2 48.3 2.520 64.0 1.744 44.3 2.638 67 2 60.3 3.051 77.5 2.217 56.3 3.071 78 21/2 76.1 3.583 91 2.839 72.1 2.953 75 3 88.9 4.173 106 3.319 84.3 3.169 80.5 DIN 32676 SERIES C (ASME BPE) Nominal hose size Flange diameter D Outlet diameter I *Fitting length A in in mm in mm in mm 1/4 0.984 25.0 0.180 4.57 1.299 33 3/8 0.984 25.0 0.305 7.75 1.654 50 1/2 0.984 25.0 0.370 9.4 1.732 50 3/4 0.984 25.0 0.620 15.75 1.969 50 1 1.988 50.5 0.870 22.1 2.283 58 11/2 1.988 50.5 1.370 34.8 2.638 62 2 2.520 64.0 1.870 47.5 3.071 78 21/2 3.051 77.5 2.370 60.2 2.795 75 3 3.583 91 2.870 72.9 3.169 80.5
- PFTE-lined and flared
-
PFTE-lined and flared
Introduction
Advantages are unrestricted clean flow of fluids, no fluid entrapment areas, and all PTFE wetted surfaces internally. Available as standard, stocked fittings in the listed sizes, or in other sizes to special order.
End fitting specifications
- ASME BPE
- DIN32676
- BS4825 Pt 3 - equivalent to ASME BPE
- ISO 1127
End fitting materials
- Fittings in Grade 316L SS (= BS 316 S11 = EN 1.4404)
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
Note: The inside lip of the Aflex flared face design is hot formed to a square edge. This prevents a gap for fluid entrapment between the rubber seal and the sealing face. Other suppliers designs have rounded edges, which opens a gap for fluid entrapment.
Temperature and pressure ratings
- Pressures up to 16 bar (230 psi)
- Temperatures up to 120˚C (250˚F) with EPDM gaskets
- Temperatures up to 180˚C (356˚F) with PTFE, silicone or viton gaskets
- Higher Pressures and temperatures possible with special clamps and appropriate seals.
Nominal hose size Flange diameter D Outlet diameter I *Fitting length A 3A in in mm in mm in mm Mini-Sanitary Triclamp Fittings **3/8 0.984 25.0 3/8 9.5 2.2 56 √ **1/2 0.984 25.0 3/8 9.5 2.3 60 √ Sanitary Triclamp Fittings **5/8 (DN15) 1.340 340 5/8 16.10 3.0 77 √ 3/4 (DN20) 1.340 34.0 0.790 20.0 3.0 77 √ 3/4 1.984 50.5 3/4 19.0 2.6 65 √ 7/8 1.984 50.5 7/8 22.2 2.6 65 √ 1 1.984 50.5 1.024 26.0 2.6 65 √ 13/8 1.984 50.5 13/8 34.9 2.8 72 √ 11/2 1.984 50.5 13/8 34.9 3.2 80 √ 17/8 2.516 64.0 17/8 47.6 3.3 84 √ 2 2.516 64.0 17/8 47.6 3.6 91 √ 21/2 3.050 77.5 23/8 60.2 5.3 135 √ 3 3.580 91.0 27/8 72.9 5.6 142 √
- RJT female fitting, non-lined
-
RJT female fitting, non-lined
Nominal hose ize *Fitting Length A (Bioflex Ultra A) Fitting Inside Diameter I Weight of Fitting in mm in mm in mm kg lbs 1 25 2.04 52 0.85 21.50 0.40 0.88 11/2 40 2.44 62 1.25 31.75 0.75 1.65 2 50 2.83 72 1.75 44.45 1.02 2.48 * Fitting Lengths listed are for Bioflex Ultra RC, SI and BK hose grades. Shorter lengths apply for other hose grades.
- SMS female fittings
-
SMS female fittings
End fitting specifications
- SMS generally to Swedish SMS1148 specification.
- RJT generally to British BS4825 Pt 5 specification.
End fitting materials
- Spigots in Grade 316L SS
- Nuts in Grade 304 SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316L SS
90˚ elbows
- PTFE Lined 90° elbow fittings are available for some sizes and grades.
Temperature and pressure ratings
- Pressures up to 10 bar (150 psi)
- Temperatures up to 150˚C (302˚F).
Surface finish: Non-lined fittings only
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Nominal hose size *Fitting length A
(Bioflex Ultra RC)Fitting inside diameter I Weight of fitting †3A in mm in mm in mm kg lbs 1 25 3.39 86 1 25.7 0.40 0.88 √ 11/4 32 3.39 86 11/4 32.4 0.51 1.12 √ 11/2 40 3.70 94 11/2 38.9 0.73 1.60 √ 2 50 4.10 104 2 51.6 1.10 2.42 √ 21/2 65 6.38 162 21/2 63.7 1.78 3.92 √ 3 80 6.85 174 3 76.8 2.15 4.73 √ * Fitting Lengths listed are for Bioflex Ultra RC, SI and BK hose grades. Shorter lengths apply for other hose grades.
† 3A - Clean out of place (COP) only.
- PFTE- lined flange
-
PFTE- lined flange
Flange specifications
- ANSI B16.5 (also ASME B16.5) Class 150# and 300#
- *DIN PN10, PN16 and PN40
- JIS 10K
- Other pressure ratings and flange specifications are also available.
*DIN PN10, PN16 and PN40 Flanges all have the same dimensions, and so are fully interchangeable
Maximum Pressure Ratings for Flange Fittings
ANSI 150# = 16 bar (230 psi), ANSI 300# = 41.4 bar (600 psi)
DIN PN10 = 10 bar (145 psi), DIN PN16 = 16 bar (230 psi)
DIN PN40 = 40 bar (580 psi)End fitting materials
- Flanges in Grade 304 SS
- Flange retainers in Grade 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316 SS
Alternative options for flange component only
- Zinc plated carbon steel
90° elbow flange fittings
- 90˚ elbow integral PTFE-lined flange fittings are available for sizes 1”, 11/2” and 2”
IMAGE
Nominal hose size *Fitting length A
(Bioflex Ultra RC)
ASA*Fitting length A
(Bioflex Ultra RC)
PN**Flared diameter D Fitting inside Dia. & Hose Bore I Recommended Bolt Tightening Torques Weight of Fitting †3A ANSI 150# DIN PN10/16 in mm in mm in mm in mm in mm in mm ft.lbs N.m kg lbs 1/2 13 2.24 57.0 2.28 58 **1.25 **32 **1.25 **32 1/2 13.0 8 11 0.54 1.20 - 3/4 20 1.89 48.0 1.93 49 1.69 43 **1.97 **50 3/4 19.4 8 11 0.88 1.90 √ 1 25 2.40 61.0 2.48 63 2.00 50 **2.50 **63 1 25.7 10 14 0.96 2.10 √ 11/4 32 2.24 57.0 2.32 59 2.48 63 3.10 78 11/4 32.4 12 16 1.15 2.53 √ 11/2 40 2.36 60.0 2.44 62 2.875 73 3.50 88 11/2 38.9 15 20 1.75 3.80 √ 2 50 2.72 69.0 2.91 74 3.625 92 4.00 102 2 51.6 25 34 2.70 5.95 √ 21/2 65 4.86 123.5 4.86 123.5 4.13 105 4.80 122 21/2 63.7 30 41 4.21 9.26 √ 3 80 5.17 131.4 5.17 131.4 5.00 127 **5.00 **127 3 76.8 40 54 4.75 10.44 √ Step-Up’ PTFE-lined flange fitting design for Bioflex Ultra Hose
Because Bioflex Ultra Hose has better flow rates than some larger bore sizes of Convoluted PTFE hose, it represents a superior alternative when fitted with the larger size flanges in some applications.
It is, however, necessary to also “Step-Up” the PTFE-lined bore, to ensure a diameter match with the mating connector.
This is best achieved using a solid PTFE Adaptor Plate, as shown in the drawing.
- Swivel flange fittings
-
Non-lined Swivel flange fittings
Flange specifications
- ANSI B16.5 (also ASME B16.5) Class 150# and 300#
- *DIN PN10, PN16 and PN40
- JIS 10K
- Other pressure ratings and flange specifications are also available.
*DIN PN10, PN16 and PN40 Flanges all have the same dimensions, and so are fully interchangeable
End fitting materials
- Flanges normally in Grade 304 SS, or Grade 316 SS if required
- Flange Retainers in Grade 316L SS
- Ferrules, most in Grade 304 SS, some sizes in Grade 316 SS
Surface finish
- All surface finishes are to ASME BPE-SF-O (no finish required).
- If a specified finish on a particular surface is required, please state on the enquiry and order.
Alternative options for flange component only:
Zinc plated carbon steel
Maximum pressure ratings
- ANSI 150# = 16 bar (230 psi),
- ANSI 300# = 41.4 bar (600 psi)
- DIN PN10 = 10 bar (145 psi),
- DIN PN16 = 16 bar (230 psi)
- DIN PN40 = 40 bar (580 psi)
Nominal hose size *Fitting length A
ASA150Flared diameter D
ASA150Fitting inside diameter I
ASA150Weight of fitting †3A in mm in mm in mm in mm kg lbs 1/2 13 1.67 42.50 1.38 35.00 0.37 9.40 0.57 1.25 - 3/4 20 1.86 47.24 1.69 42.90 0.62 15.75 0.84 1.84 √ 1 25 2.36 60.00 2.00 50.80 0.85 21.50 1.20 2.63 √ 11/4 32 2.67 67.72 2.50 63.50 1.03 26.21 1.59 3.50 √ 1 1/2 40 2.75 69.86 2.87 73.00 1.25 31.75 2.15 4.73 √ 2 50 3.20 81.22 3.62 92.00 1.76 44.60 2.92 6.41 √ 21/2 65 3.70 94.00 4.13 105.00 2.25 57.15 4.36 9.59 √ 3 80 3.74 95.00 5.00 127.00 2.63 66.70 6.02 13.24 √ Nominal hose size *Fitting length A
PN10/16Flared diameter D
PN10/16Fitting inside diameter I
PN10/16Weight of fitting †3A in mm in mm in mm in mm kg lbs 1/2 13 1.79 45.50 1.77 45.00 0.37 9.40 0.78 1.72 - 3/4 20 2.11 53.50 2.28 58.00 0.62 15.75 1.12 2.47 √ 1 25 2.44 62.00 2.68 68.00 1.12 28.50 1.43 3.15 √ 11/4 32 2.70 68.50 3.07 78.00 1.03 26.21 2.35 5.17 √ 11/2 40 2.91 74.00 3.49 88.00 1.70 43.10 2.76 6.06 √ 2 50 3.50 89.00 4.02 102.00 2.15 54.50 3.62 7.96 √ 21/2 65 3.62 92.00 4.80 122.00 2.25 57.15 4.58 10.07 √ 3 3.74 95.00 5.43 138.00 2.63 66.70 6.03 13.26 √ * Fitting lengths listed are for Bioflex Ultra RC, SI and BK hose grades. Shorter lengths apply for other hose grades.
† 3A - Clean out of place (COP) only.
Kapcsolatfelvétel az Aflex Hose csapatának specialistájával
Ha kérdése van, vagy terméket kíván rendelni, hívja a következő számot: +36 1 445 3256, vagy